Electrolux EQBH60AS Manuel d'utilisateur télécharger pdf (Page 11)

electrolux integrated bbq 600/300mm universal LPG installation 11

Preparing the unit for Universal LPG installation

This barbecue is supplied set up for Natural Gas and is

labelled accordingly. A Universal LPG conversion kit is

available from Electrolux Spare Parts to enable conversion

to Universal LPG and connection to a 9kg bottle.

Remote ULPG supply

The barbecue can be plumbed into a remote or

household ULPG supply. Never connect the barbecue

to an unregulated supply, ensure supply pressure at the

barbecue is 2.75kPa. Electrolux strongly recommends that

a manual shut off valve be installed in the gas supply line in

an accessible position so that gas can be turned off in the

event of an emergency, or during servicing.

NOTE:

Conversion of this unit to Universal LPG must be carried

out by a qualiﬁed licensed person and a Certiﬁcate of

Compliance must be issued to the owner on completion

of the installation and conversion. The components are:

For models EQBH60AS & EQBL60AS

• Hose and regulator assembly

• Small plastic bag containing 4 brass injectors (0.90mm)

• 1 Universal LPG sticker

• 1 brass adaptor

• 1 sealing washer

For models EQBL30AS

• Hose and regulator assembly

• Small plastic bag containing 1 brass injector (0.90mm)

• 1 Universal LPG sticker

1. Change the injectors

• Remove the front cover.

• Remove the burner retaining clips as shown.

remove spring clip

by rotating over

burner tube end

front cover

• Unscrew and replace the injector nipples located in the

end of each tube feeding the burners. The Universal LPG

injectors have a 0.90mm diameter oriﬁce in them. They

appear substantially smaller than the Natural Gas injectors.

LPG injector

• Re-fasten the clip to retain the tube in the burner.

Do not over tighten or distort supply tube.

• Fit the front cover back on and fasten screws.

2. Adjust the turndown setting on the valve

• Remove the knobs from the valves.

• Remove rubber grommets from control panel holes.

• For each valve rotate the valve rotation limiting screw

anti-clockwise using a Philips head screw driver until

valve shaft is able to be rotated more than 180°

(approx 3 turns).

Valve rotation

limiting screw

• Re-t grommets and knobs

3. For EQBH60AS & EQBL60AS only, connect the adaptor

to the barbecue gas inlet. Ensure the blue sealing

washer is in place. Do not over tighten.

4. Connect the hose. Do not over tighten.

5. Following connection to gas bottle, conduct a leak test

for all joints made (refer leak test procedure page 12).

6. Light all burners and one at a time set the burner to the

lowest setting and check a small steady ﬂame is achieved.

EQBH60AS & EQBL60AS

barbecue gas inlet

sealing washer

brass adaptor

LPG hose and

regulator assembly

EQBL30AS

LPG hose and regulator assembly

gas inlet

7. Replace the ‘gas type’ sticker

• Locate the ‘Natural Gas’ sticker located on or near the gas

inlet and remove it. Put the Universal LPG sticker in its place.

Universal LPG installation

INTBBQ600/300_Jun11.indd 11 30/06/11 11:52 AM

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

Electrolux EQBH60AS Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Non Electrolux EQBH60AS